Sunday, 6 November 2022

009 Chiemsee-Bahn Style Steam Tram

© 2022 David Hurst All Rights Reserved

Following on the theme of the steam trams I had a look at European types and found some really good candidates to suit the new Kato-Peco Small England chassis, one stood out for me, the meter gauge Chiemsee-Bahn tram looked a perfect match for the chassis.

© 2022 David Hurst All Rights Reserved


The Chiemsee-Bahn (Chiemsee Railway) is a meter gauge line in Prien am Chiemsee, Germany. It is one of the world's last steam tramways and is said to be the oldest continuously operated steam tramway in regular operation.

It has worked out as a very compact model, and as such, I have ended up adding the couplings to the buffer plates and not using the Peco coupling pockets which I would normally use. It is a superb running model and I think my favorite tram from my ever-growing collection.



© 2022 David Hurst All Rights Reserved

To allow for fitting details inside the very small space in the cab that is left after accommodating the chassis and the large weight. I have made the whole of the upper cab including the roof and supports separate from the lower body. This has allowed me to fit a figure with its lower half removed. I used one of the Dapol trackside work crew. It also makes it possible to add pipework and controls if you like.

© 2022 David Hurst All Rights Reserved

There is a bit of deviation from the original tram around the smoke box door, this was purely for the structural stability of the roof supports and to locate the upper and lower sections. The smoke box door is printed as a separate part, I used a dart from RT models.

© 2022 David Hurst All Rights Reserved

The handrails have small pilot holes formed to give a guide for drilling out to suit the wire used. My choice was 0.45mm brass. There are three small lamps added with the print, two for the front of the tram and one for the rear, I added some clear and red rhinestones to form the lenses on these. There are holes in the front of the bodywork for the lamps, but you can decide if you want to fit the rear one and where to position it.

© 2022 David Hurst All Rights Reserved

One of my modifications on the prototype was to abandon the NEM pockets and to fit a set of RT models Penryhn Locomotive couplings, as space is a premium inside the lower bodywork. I have added a similar printed pair to the model on Shapeways now also some location holes on the buffer beams.

© 2022 David Hurst All Rights Reserved

Finishing the model was done in oil-based enamels, the black was Revell M09 Anthracite and the green was a mix, not as bright as the original. The roof was left in the grey primer. The lining used is Fox Transfers cream 0.35mm, and this is sealed with a matt varnish.

© 2022 David Hurst All Rights Reserved

It goes well with a small tram coach which I converted from an Atlas tram model obtained on eBay.This started out as a Berlin tram in a 1:86 scale which I added a 4mm section between the footplate and the bodywork to raise its height and give it the height to look like a 4mm scale model. Under the footplate I used a Peco wagon frame split in half to extend the wheelbase and some etched brass mesh to form side guards to the chassis. The foot plate being of metal gives it enough weight. Because of using the Peco wagon frame, I was able to fix Peco NEM pockets and couplings directly under the footplate. With the paintwork being superb on the Atlas models I decided to keep it untouched, the additional section that I added was painted in a contrasting darker green and the footplate was lined in red.

© 2022 David Hurst All Rights Reserved

I have made this model available on Shapeways if you would like a copy of the print. see the link below.

009 Chiemsee-Bahn Steam Tram (649WKSZ4H) by tdhurst (shapeways.com)